Cleverly installed cylinders in winter, due to cold weather, the water blocking ring becomes brittle, and it is easy to break when installed on the cylinder liner. Before installation, the water stop ring can be soaked in warm water of about 60°C for 5 minutes. After the removal, the installation is not easy to break.
Cleverly mounted rolling bearing When installing a rolling bearing, directly hit with a hammer, easily deforming the bearing and affecting its service life. A simple installation method is now introduced: Select a 600 watt bulb to be connected to a power supply, and use it to heat the bearings to be installed. The heating time is 5 to 10 minutes. The heating temperature is maintained at about 110°C. Do not exceed 120°C. Quickly install the bearing on the shaft.
Cleverly repairing the clutch pedal pedal When the cross bar is flattened, the foot easily slides out when the pedal is pressed. Rainy days are easy to slip. If a suitable length of rebar is welded on both the upper and the lower side of the pedal, the rebar plane will be 5 mm above the pedal plane so that it will not slip when used.
Clever row oil pump air The rotor oil pump used in the S195 diesel engine, if the pump air is not drained, there will be no oil pump failure, the trick is to use a medical waste needle pipe full of oil, to the pump Fill the oil inlet and turn the oil pump so that the outlet discharges oil.
Break the paper pad to make a good repair at the break. Apply a little butter on both sides of the paper pad, cut two white papers of the same size as the paper pad, stick them on both sides of the paper pad, and put them on the machine. Tighten the nuts to eliminate leakage.
Qiaozhi tire leakage to take two tablespoons of talcum powder, pull down the valve core, put up the inner tube air, made of a paper funnel into the middle, will talc poured into the inner tube. Then fill the valve core with sufficient gas, talcum powder in the tire was diffusely attached to the inner wall, you can block the small air leakage.
Cleverly dismantling the outer elastic ring of the deceleration gear and the external elastic ring of the deceleration gear in the Dongfeng-12 type tractor's gearbox are very difficult to disassemble. A fine wire can be used to pass through the small hole in the retaining ring and screw it tightly. The other end is screwed up with a screwdriver and tightly pulled. Then the drive wheel is rotated back and forth several times to remove the retaining ring.
It is not easy to remove dirt and dirt from the fine dirt filter inside the fine filter in the fine filter. If a layer of paper is applied to the inner wall of the rotor with butter, and the soil is attached to the paper, the paper can be removed and the soil can be completely removed.
Investigate cracks in parts carefully Put the parts into kerosene, remove them after a while, dry the surface and sprinkle with a layer of white powder. Then tap the parts with a small hammer. If there is any crack, it will be immersed in cracks due to hammer vibration. The kerosene leaked from the cracks and the cracks appeared on the white powder.
Clever demolition of the old cylinder liner with the previous old piston pin into the aircraft's old piston, install one or two old piston rings on the old piston, with a small diameter steel 6.50 mm hooked the old piston pin, the piston is installed in reverse Into the cylinder, when the piston ring exceeds the lower edge of the cylinder liner, it will automatically pop up and get stuck in the cylinder liner. At this time, the small steel bar is wound on the wooden stick, and then the wooden rod is lifted to remove the missing sleeve. .
Cleverly mounted rolling bearing When installing a rolling bearing, directly hit with a hammer, easily deforming the bearing and affecting its service life. A simple installation method is now introduced: Select a 600 watt bulb to be connected to a power supply, and use it to heat the bearings to be installed. The heating time is 5 to 10 minutes. The heating temperature is maintained at about 110°C. Do not exceed 120°C. Quickly install the bearing on the shaft.
Cleverly repairing the clutch pedal pedal When the cross bar is flattened, the foot easily slides out when the pedal is pressed. Rainy days are easy to slip. If a suitable length of rebar is welded on both the upper and the lower side of the pedal, the rebar plane will be 5 mm above the pedal plane so that it will not slip when used.
Clever row oil pump air The rotor oil pump used in the S195 diesel engine, if the pump air is not drained, there will be no oil pump failure, the trick is to use a medical waste needle pipe full of oil, to the pump Fill the oil inlet and turn the oil pump so that the outlet discharges oil.
Break the paper pad to make a good repair at the break. Apply a little butter on both sides of the paper pad, cut two white papers of the same size as the paper pad, stick them on both sides of the paper pad, and put them on the machine. Tighten the nuts to eliminate leakage.
Qiaozhi tire leakage to take two tablespoons of talcum powder, pull down the valve core, put up the inner tube air, made of a paper funnel into the middle, will talc poured into the inner tube. Then fill the valve core with sufficient gas, talcum powder in the tire was diffusely attached to the inner wall, you can block the small air leakage.
Cleverly dismantling the outer elastic ring of the deceleration gear and the external elastic ring of the deceleration gear in the Dongfeng-12 type tractor's gearbox are very difficult to disassemble. A fine wire can be used to pass through the small hole in the retaining ring and screw it tightly. The other end is screwed up with a screwdriver and tightly pulled. Then the drive wheel is rotated back and forth several times to remove the retaining ring.
It is not easy to remove dirt and dirt from the fine dirt filter inside the fine filter in the fine filter. If a layer of paper is applied to the inner wall of the rotor with butter, and the soil is attached to the paper, the paper can be removed and the soil can be completely removed.
Investigate cracks in parts carefully Put the parts into kerosene, remove them after a while, dry the surface and sprinkle with a layer of white powder. Then tap the parts with a small hammer. If there is any crack, it will be immersed in cracks due to hammer vibration. The kerosene leaked from the cracks and the cracks appeared on the white powder.
Clever demolition of the old cylinder liner with the previous old piston pin into the aircraft's old piston, install one or two old piston rings on the old piston, with a small diameter steel 6.50 mm hooked the old piston pin, the piston is installed in reverse Into the cylinder, when the piston ring exceeds the lower edge of the cylinder liner, it will automatically pop up and get stuck in the cylinder liner. At this time, the small steel bar is wound on the wooden stick, and then the wooden rod is lifted to remove the missing sleeve. .
The medical compressed air plant consists of the air compressor, general filter, aftercooler, precision filter, desiccant air dryer, air buffer tank, activated carbon filter, compressed air quality monitor, decompressor, valve, pipeline and terminal. The system generates compressed air through an air compressor, removes the impurities, oil mist and moisture in the compressed air through an adsorption dryer filter unit, delivers the air to the air storage tank and supplies it through a pipeline to the terminal equipment in the operating room, ICU and other inpatient wards after decompression.
Medical Compressed Air Plant
Medical Compressed Air Plant ,Hospital Gas System ,Hospital Gas Pipeline System ,Medical Air Compressor
Hunan Eter Electronic Medical Project Stock Co., Ltd. , https://www.centralgas.be